CABIN BEACH 20-05-14
20-05-14
The beach cabin is made entirely of timber. It has total dimensions: 130 cm wide, 120 cm long and 230 cm high.
It consists of four vertical wooden columns 9x9cm in height and 190cm in height from the top of which a diagonal piece has been removed to fit the two-chamber roof of the cabin.
The two sides, on the four sides of the cabin, are covered with 18mm thick birch plywood sections of 93.5×130 cm, which are located 30 cm from the wooden platform of the base.
The third side of the cabin that forms the rear of the cabin is covered up to the roof with birch plywood.
The front of the cabin features a 93.5X130 cm birch plywood door, which is held in one of the two front columns by means of two metal hinges. It also has a metal handle and latch for secure closure.
The cabin floor is made of timber. It consists of 4 woods of 9x9x93.5 cm, of which 4x4x93.5 cm and 4x20x4x99cm and 1 18,5x4x99cm wood constitute the laminate. The floor consists of 4 9x9x93,5cm wood from which 4x4x93,5cm is removed.
The roof of the cabin is two-tiered and made of 75×120 cm birch plywood.
In between the two front pillars there is a triangular shaped timber section of timber. The cabin has two double metal hangers on the inside of the rear wall.
TIMBER
The wood used. is a Swedish non-stick pine wood composite, in accordance with EN 351. It is manufactured with special compound (welding of wood) in various sections depending on the intended use.
COMPOSITE wood is 40% stronger than whole wood. It has a strength of 360 kp / m2 and a specific weight of about 480 kg / m3.
It contains about 15% moisture
Contains minimal juices (resin) compared to other pine family trees in other countries (weather in northern Sweden up to -25 ° C)
It has thermal conductivity s = 0.10 Kcal / Mho and sound insulation 3.5 times greater than concrete or brick of equal thickness.
It has antimagnetic properties and is a poor conductor of electricity
It can withstand fire and is classified in categories F30 and F60 (by DIN4120) according to its cross section.
When the outer part of the cross-section burns, its interior protects and retains its strength.
It is processed just like commercial wood
It retains its shape and distorts or creates minimal fractures
Annual wood rings are usually perpendicular to the long side of the cross-section with a significant increase in the mechanical strength of this surface when applied to floors.
All corners of the wood are planed to a radial of at least 5 mm.
PAINTED PLYWOOD BIRCH
The plywood elements required for our constructions are approximately 20 mm thick and are made of 1.5 mm thick laminated wood with pressurized heat sealant using non-toxic phenolic base resins. They are painted with water-soluble paints to which no seals, thinners or paints containing lead, chromium, cadmium or other heavy metals have been attached. The colors are also highly resistant to adverse weather conditions.
The above plywood sheets are in accordance with EN 314-2. The quality of the plywood is such that no further processing is required before painting, such as, for example, stocking, and reliefs and themes can be engraved.
PLASTIC INFORMATION
Plastic components required to manufacture the equipment are highly resistant to UV radiation and adverse weather conditions. Preferred are recyclable materials such as polyethylene (PE) or polypropylene (PP). Specifically all screws protruding from the equipment over 5 mm are covered with polypropylene (PP) plastic plugs. They are also safe for the safety and health of children.
METALLIC ELEMENTS
Metallic elements used in the manufacture of the equipment (screws, connectors, etc.) are made of metals either thermo-galvanized or electro-galvanized, where the surface preparation has been preceded by sandblasting or stainless steel. The dimensions and cross-sections of the metallic elements are sufficient to accommodate (with an appropriate safety factor) the loads for which they have been designed to withstand corrosion and adverse weather conditions.
PAINTS
The varnishes and paints that protect the wooden parts are specially designed for the climate of our country and are absolutely harmless to the users (they do not contain lead, chromium, cadmium or other heavy metals) and give high strength to our constructions.
All production work processes for the processing of raw materials are carried out according to
The ISO9001: 2015 quality system
The environmental management system ISO14001: 2015
