CLIMBING FRAMES 0010-251

 

0010-251

The horizontal scale is 112X300X240 cm and consists of:

• 4 pcs 9x9cm and 240cm cross columns
• 2 pcs horizontal beams 9x9x300 cm.
• 8 pcs galvanized hot rolled plates with a cross section F32 3 mm thick and 76 cm long.
• 6 pcs galvanized hot rolled sheets with F32 cross section 3 mm thick and 93 cm long
• 36 pcs Polypropylene (PP) F650 mm outer bolts and 30 mm high.
• 28 pcs polypropylene (PP) cyclic standstill
• 28 pcs 15mm x150mm electro galvanized screws
• 4 pcs 15mm x 250mm electro galvanized screws
• 8 pcs of 100 cm long galvanized hot rolled laminates, 3 mm thick and 97 mm wide (mounting – underground mounts)
• 4 pcs 15mm x110mm electro galvanized screws
• 4 pcs electro galvanized F15 safety nuts

This activity is made of elongated “P” shape. The two horizontal beams 300x9x9 cm (with two 15mm x220mm screws) are inserted inside the four vertical dimensions 240x9x9 cm (with two screws 15mmx220mm) and eight polypropylene (PP) fasteners.

They leave an intermediate gap of 76 cm for application of the 8 handles (F32Χ3 mm x 76 cm) at constant intervals of 30 cm between them.

The four vertical beams 240x9x9 cm are applied perpendicular to the two horizontal beams.

They leave a gap of 94 cm in between for the six climbing steps, three on each side (F32 thickness 3 mm X94 cm) positioned: 1 in 40 cm off the ground and the rest in 30 cm between them.

All laminates are fitted with 28 15mm X150mm 28 screws and carry 28 polypropylene (PP) safety plugs externally and 28 polypropylene (PP) circular suspensions internally for complete fit and safety.

BACKPACK BASES

For fixing the instrument to the ground, each pair has a pair of mounting bases.

The mounting bases consist of two galvanized metal plates and then painted with electrostatic paint, of a shape “P” and approximately 100x12x4 cm thick and 0.5cm thick, which “embrace” the column and are joined by passing screws 5 / 8 ″ X15. At the bottom there is a metal flange to hold them in the concrete pit.

Only ground irons, which hold the column at least 5 cm above the ground, are prevented from being ground in order to prevent the wood from being eroded by soil moisture.

TIMBER

The wood used is composite non-stick Swedish pine timber, in accordance with EN 351. It is manufactured with a special compound (welding of wood) in various sections depending on the intended use.

COMPOSITE wood is 40% stronger than whole wood. It has a strength of 360 kp / m2 and a specific weight of about 480 kg / m3.

• Contains about 15% moisture
• Contains minimal juices (resin) compared to other pine family trees in other countries (weather in northern Sweden up to -25 ° C)
• Has thermal conductivity s = 0.10 Kcal / Mho and sound insulation 3.5 times greater than concrete or brick of equal thickness.
• Has antimagnetic properties and is a poor conductor of electricity
• Resistant to fire and classified in categories F30 and F60 (by DIN 4120) according to its cross-section.
• When the outer part of the cross-section burns, its interior protects and retains its durability.
• It is processed just like commercial wood
• Maintains its shape and distorts or creates minimal fractures
• Annual wood rings are usually perpendicular to the long side of the cross-section with a significant increase in the mechanical strength of this surface when applied to floors.

All corners of the wood are planed with a radius of about 5 mm.

PAINTED PLYWOOD BIRCH

The plywood elements required for our constructions are approximately 20 mm thick and are made of 1.5 mm thick laminated wood with pressurized heat sealant using non-toxic phenolic base resins. They are painted with water-soluble paints to which no seals, solvents or dyes containing lead, chromium, cadmium or other heavy metals have been attached. The colors are also very resistant to adverse weather conditions.

The above plywood sheets are in accordance with EN 314-2. The quality of the plywood is such that no further processing is required before painting, such as, for example, stocking, and reliefs and themes can be engraved.

 

PLASTIC INFORMATION

The plastic components required to manufacture the equipment are highly resistant to UV radiation and adverse weather conditions. Preferred are recyclable materials such as polyethylene (PE) or polypropylene (PP). Specifically all screws protruding from the equipment over 5 mm are covered with polypropylene (PP) plastic plugs. They are also safe for the safety and health of children.

METALLIC ELEMENTS

The metallic elements used in the manufacture of the equipment (screws, connectors, etc.) are made of metals either thermo-galvanized or electro-galvanized, where the surface preparation has been preceded by sandblasting or stainless steel. The dimensions and cross-sections of the metallic elements are sufficient to accommodate (with an appropriate safety factor) the loads for which they have been designed to withstand corrosion and adverse weather conditions.

PAINTS

The varnishes and the colors that protect the wooden parts are specially designed for the climate of our country (temperature changes, open or closed areas etc.) are completely harmless to the users (they do not contain lead, chromium, cadmium and other heavy metals). ) and give great durability to our constructions.

PACKING

The following procedure is used for fixing the equipment:

At this point where the column is to be placed, an 80 cm deep pit is opened. about 60cm in diameter. Then, once the column is inserted, the pit is filled with frusto-concreted concrete until it reaches 20 cm. from the ground surface, where it is covered with soil.

Only ground irons, which hold each column at a distance of about 10 cm from the ground, are prevented on the ground in order to prevent the wood from corroding the soil moisture.

 

All production work processes for the processing of raw materials are carried out according to:

• EN 1176 standards 1-6,
• ISO 9001: 2015 quality system
• The ISO 14001: 2015 environmental management system