TECHNICAL DESCRIPTION
COMPOSITE METALLIC INSTRUMENT
MOD. 10 – 08-05
The composite instrument 10 – 08-05 has a total dimensions of 450×120 cm and a height of 362 cm and includes:
1 square loft 122 cm high
1 staircase for loft 122 cm
1 square cover
1 corrugated slide height 122 cm
Protective place
SQUARE LOFT 122 cm (with square cover)
The 122 cm loft has a total dimensions of 111,5X111,5X362 cm and consists of:
4 wooden pillars 9X9 cm and 302 cm high
4 wood 9X9X93.5 cm from which approximately 4x4x93.5 cm is removed along a piece
1 Wireness Plywood, one side of which features a dark brown, non-slip floor. Its dimensions are 99X99 cm and its thickness is 21mm.
1 square polyethylene cover that applies to the top of the 4 columns.
The vertical wooden columns of 302 cm height are pierced at points of about 116 cm and 117 cm, one on each of the sides connected to the loft, from their base to the floor of the loft. These holes are fitted with Ø15 mm metal rods with a length of 75 mm.
It has two nuts in the corresponding height mounted on the wood hole. Fits with two 3 / 8X13 screws. The opening of the wood hole is sealed with a polypropylene (PP) plug.
The floor consists of 4 9x9x93.5cm woods on which the wireness plywood that forms the loft floor is supported.
STAIRCASE LADDER 122 CM (FOR AGES 1 AND OVER)
The 122 cm high staircase ladder measures 93X172 cm and surface area 114 cm. Consists of:
2 wood 4,5x20x172 cm
6 woods 4,5x20x84,5 cm
6 woods 4,5x6x84,5 cm
The 122 cm staircase handrail consists of:
4 wood with curved edges 4,5x9x90 cm
2 woods with curved edges approximately 4,5x9x160 cm.
2 specially shaped rectangular birch plywood colored with internal angles of about 45 ° and 135 °, inscribed in a rectangular rectangle of approximately 110×230 cm, 2 cm thick.
Between the 2 x 20×172 cm woods there are 6 4,5x6x84,5 cm woods per 20 cm. The 6x 4,5x20x84,5 cm woods are applied on them.
The handrail is made as follows: The 2 woods 4.5x9x160 cm are facing each other and facing upwards. In these, they are screwed vertically 4,5 x 9×90 cm 2 by 2 on each side. Between the 20x 172cm stairs, the 4.5x9x160cm stairs and the 4.5x9x90cm vertical stairs, the rectangular gap on each side of the staircase is covered with birch plywood.
SQUARE COVER
The square cover is approximately 122x122x70cm long and 102.5 cm long from center hole to center hole on each side.
The lid is manufactured by the rotary extraction molding process. It is formed of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.
Each color, which is non-toxic, is applied by rotary extraction of the mold. These materials are disciplined by:
ASTM – D – 790 (Flex Modulus – Flexible Components)
ASTM – D – 638 (Tensile Strength)
ASTM – D – 648 (Heat Distortion Temperature – Heated Distortion)
ARM – STD (Low Temperature Impact – low temperature impact effect)
ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.
STRAIGHT CORRUGATED SLIDE 122 CM.
The straight corrugated slide has a height of about 122 cm and a projection length of 215 cm.
It is manufactured by the rotary extraction method. It consists of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.
Each color, which is non-toxic, is applied by rotary extraction of the mold. It is a one-piece and mounted with a one-piece Hood cover of the same material, for protection against falls
These materials are disciplined by:
ASTM – D – 790 (Flex Modulus – Flexible Components)
ASTM – D – 638 (Tensile Strength)
ASTM -D- 648 (Heat Distortion Temperature- Heated Distortion)
ARM – STD (Low Temperature Impact – low temperature impact effect)
The diameter of the side walls should be at least 5 cm thick.
Exceptions should be mentioned.
ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.
HOODS
The slide guard protects children from leaving their seats in order to avoid accidents. It is 105 cm high, 87 cm wide and approximately 10 cm wide.
They are manufactured by the method of rotary extraction into molds. It consists of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.
Each color, which is non-toxic, is applied by rotary extraction of the mold.
These materials are disciplined by:
ASTM – D – 790 (Flex Modulus – Flexible Components)
ASTM – D – 638 (Tensile Strength)
ASTM – D – 648 (Heat Distortion Temperature – Heated Distortion)
ARM – STD (Low Temperature Impact – low temperature impact effect)
ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.
PROTECTIVE FRAMEWORK
The protective frame measures approximately 85X97X6 cm. It consists of:
2 wooden columns approximately 4x6x97 cm.
1 plywood of colored birch approximately 85,5X90X2 cm.
Between the pillars is placed the birch plywood, about 85,5x90x2 cm, in which relief figures or themes can be carved. The protective frame is positioned in a flat above the loft floor and is secured to the loft pillars.
TIMBER
The wood used for its equipment is composite non-stick Swedish pine timber, in accordance with EN 351. It is manufactured with special compound (welding of wood) in various cross sections depending on the intended use.
COMPOSITE wood is 40% stronger than whole wood. It has a strength of 360 kp / m2 and a specific weight of about 480 kg / m3.
It contains about 15% moisture
Contains minimal juices (resin) compared to other pine family trees in other countries (weather in northern Sweden up to -25 ° C)
It has a thermal conductivity of s = 0.10 Kcal / Mho and sound insulation 3.5 times greater than concrete or bricks of equal thickness.
It has antimagnetic properties and is a poor conductor of electricity
It is resistant to fire and is classified in categories F30 and F60 (by DIN 4120) according to its cross-section.
When the outer part of the cross-section burns, its interior protects and retains its strength.
It is processed just like commercial wood.
It retains its shape and distorts or creates minimal fractures.
Annual wood rings are usually perpendicular to the long side of the cross-section with a significant increase in the mechanical strength of this surface when applied to floors.
All corners of the wood are planed with a radius of about 5 mm.
PLYWOOD BIRCH WITH SMALL FILM TWO-SIDED
The plywood elements required for our construction are approximately 18 mm thick and are made of 1.5 mm thick timber sheets welded together under pressure sealing using non-toxic resins. They have a special colored film on both sides with no seals, thinners or paints containing lead, chromium, cadmium or other heavy metals attached. The color film is highly resistant to adverse weather conditions.
The above plywood sheets are in accordance with EN 636-3 (for outdoor use). The quality of the plywood is such that sculptures and themes can be engraved.
PLASTIC INFORMATION
The plastic components required to manufacture the equipment are highly resistant to UV radiation and adverse weather conditions. Preferred are recyclable materials such as polyethylene (PE) or polypropylene (PP). Specifically all screws protruding from the equipment over 5 mm are covered with polypropylene (PP) plastic plugs. They are also safe for the safety and health of children.
METALLIC ELEMENTS
The metallic elements used in the manufacture of the equipment (screws, connectors, etc.) are made of metals either thermo-galvanized or electro-galvanized, where the surface preparation has been preceded by sandblasting or stainless steel. The dimensions and cross-sections of the metallic elements are sufficient to accommodate (with an appropriate safety factor) the loads for which they have been designed to withstand corrosion and adverse weather conditions.
PAINTS
The varnishes and the colors that protect the wooden parts are specially designed for the climate of our country (temperature changes, open or closed areas etc.) are completely harmless to the users (they do not contain lead, chromium, cadmium and other heavy metals) and give great durability to our constructions.
For their anticorrosive protection, the metal parts are processed to release them, followed by a coating of polyzinc (zinc) and then electrostatic, two-layer polyester powder coating.
PACKING
The following procedure is used for fixing the equipment:
At this point where the column is to be placed, a pit of 60 cm depth is opened. about 50cm in diameter. Then, once the column is inserted, the pit is filled with frusto-concreted concrete until it reaches 10 cm. from the ground surface, where it is covered with soil.
The ground holds only the metal standings that hold each pillar at a height of about 10 cm from the ground to prevent the wood from corroding the soil moisture.
All production work processes for the processing of raw materials are carried out according to:
EN 1176 standards 1-6,
The ISO 9001: 2015 quality system
The ISO 14001: 2015 Environmental Management System
