SWINGS 0010-230Ν

 

0010-230N

The two-seater swing has dimensions: 210 cm high and 280 cm wide. It consists of a horizontal hot-rolled metal cross section of Ø 2.5 ″ and a length of 260 cm which ends at each end in an 8 mm trapezoidal flange. Four 9x9cm, 220cm sloping beams that are connected in two “L” shape on each side of the swing. Two trapezoidal flanges similar to those of a horizontal beam of approximately 3 mm thick.

The flanges at the ends of the horizontal beam are connected to the sloping beams and 3 mm thick flanges with four M12X35 mm screws and safety nuts.

9X9X220cm sloping beams are joined to form an isosceles triangle based on 177cm and 220cm side length.

The horizontal metal beam is mounted on four bearings in specific dimensions (both between them and the sloping beams). The couplings are arranged in pairs leaving a gap (between pairs) of 55 cm and a swing of 48 cm. The intermediate gap between the two pairs is 54 cm, according to standard EN 1176.

To attach the chain to the coupler, nautical keys are used, which secure with a safety nut. For joining the chain to the seat at the other end of the chain, nautical keys are also used.

The flat seat is of heavy construction type, is internally made of 345 MPa (91 mm) flat steel plate (50,000 psi) and has 8 mm diameter molded metal joints made of 304 stainless steel with 586 Mpa. 85,000 psi). The exterior of the seat is made of soft, comfortable black rubber.

They are slow ignition and provide high resistance to various chemicals. They are with UV stabilizers and provide antistatic protection.

On the sloping beams are mounted 9x9x65 cm mounting brackets with 5 / 8×110 mm bypass screws. and a depth of 60cm. on the ground where the swing is to be mounted and the mounts are mounted in. The dimensions for opening the pits are accurately shown in the Installation drawing.

Fill the cavity with a cement up to 40cm. and the rest with the soil we removed during the pit excavation. The crib is ready for use after 48 hours. To avoid using it before 48 hours, we may not use the seats.

An important detail of the flooring is that the timber should not be touched to the ground so as not to be eroded by soil moisture. Only ground mounts are fastened to the ground. Above

them there is the Ground Line. It is a line beneath which the soil with which we filled the sump should not be removed.

A safe area of ​​750X350cm is required for proper swing operation. Lifting is not required for the swing. For better and easier use of the swing by the users, the best location for mounting it is the northwest. When in this position, users are not blinded by the sun.

TIMBER

The wood used is composite non-stick Swedish pine timber, in accordance with EN 351. It is manufactured with a special joint (wood glue) in various cross sections depending on its intended use.

COMPOSITE wood is 40% stronger than whole wood.

It has a strength of kp / m2 = 360 and a specific gravity of about 480 kg / m3.

It contains about 15% moisture.

It has thermal conductivity s = 0.10Kcal / Mho and sound insulation 3.5 times greater than concrete or brick of equal thickness.

It has antimagnetic properties and is a poor conductor of electricity.

It withstands fire and is classified in categories F30 and F60 (by DIN 4102) according to its cross-section.

When the outer part of the cross-section burns, its interior protects and retains its strength.

It is processed like commercial wood.

Retains its shape and is slightly deformed or cracked,

 

Annual wood rings are usually perpendicular to the long side of the cross-section with a significant increase in the mechanical strength of this surface when applied to floors.

PLASTIC INFORMATION

The plastic components required to manufacture the equipment are highly resistant to UV radiation and adverse weather conditions. Preferred are recyclable materials such as polyethylene (PE) or polypropylene (PP). Specifically all screws protruding from the equipment over 5 mm are covered with polypropylene (PP) plastic plugs. They are also safe for the safety and health of children.

METALLIC ELEMENTS

The metallic elements used in the manufacture of the equipment (screws, connectors, etc.) are made of metals either thermo-galvanized or electro-galvanized, where the surface preparation has been preceded by sandblasting or stainless steel. The dimensions and cross-sections of the metallic elements are sufficient to accommodate (with an appropriate safety factor) the loads for which they have been designed to withstand corrosion and adverse weather conditions.

 

PAINTS

The varnishes and the colors that protect the wooden parts are specially designed for the climate of our country (temperature changes, open or closed areas etc.) are absolutely harmless to the users (they do not contain lead, chromium, cadmium and other heavy metals). ) and give great durability to our constructions.

For their anticorrosive protection, the metal parts are processed to release them, followed by a coating of polyzinc (zinc) and then electrostatic, two-layer polyester powder coating.

 

PACKING

 

The following procedure is used for fixing the equipment:

At this point where the column is to be placed, an 80 cm deep pit is opened. about 60cm in diameter. Then, once the column is inserted, the pit is filled with frusto-concreted concrete until it reaches 10 cm. from the ground surface, where it is covered with soil.

Only ground irons, which hold each column at a distance of about 10 cm from the ground, are prevented on the ground in order to prevent the wood from corroding the soil moisture.

 

All production work processes for the processing of raw materials are carried out according to:

EN 1176 standards 1-6,

The ISO 9001: 2015 quality system

The ISO 14001: 2015 Environmental Management System