WOODEN STRUCTURE 0010-211B

 

The composite instrument has a total dimension of 450×120 cm and a height of 362 cm and includes:

 

• 1 square loft 122 cm high
• 1 staircase for loft 122 cm.
• 1 square cover
• 1 corrugated slide height 122 cm.
• protective smile

 

SQUARE 122 cm (with square cover)

The 122 cm loft has a total dimensions of 111,5X111,5X362 cm and consists of:

• 4 wooden pillars 9X9 cm and 302 cm high.
• 4 9x9x93.5 cm wood from which approximately 4x4x93.5 cm is removed along a piece.
• 1 Wireness Plywood, one side of which features a dark brown, non-slip floor. Its dimensions are 99X99 cm and its thickness is 21mm.
• 1 square polyethylene cover that applies to the top of the 4 columns.

The vertical wooden columns 302 cm high are pierced at points about 116 cm high and 117 cm high, one on each of the sides connected to the loft, from their base to the floor of the loft. These holes are fitted with π 15 mm steel bores with a length of 75 mm. It has two nuts in the corresponding height mounted on the wood hole. Fits with two 3 / 8X13 screws. The opening of the wood hole is sealed with a polypropylene (PP) plug.

The floor is made up of 4 9x9x93.5 cm wood on which the laminate flooring is the wireness.

 

STAIR FOR STAR 122 cm (for ages 1 and over)

 

The staircase for height 122 cm has dimensions 93X172 cm and surface area 114 cm. Consists of:

• 2 wood 4.5,520×172 cm
• 6 woods 4,5x20x84,5 cm.
• 6 woods 4,5x6x84,5 cm.

The stair handrail for the staircase 122 cm consists of:

• 4 wood with curved edges 4,5x9x90 cm.
• 2 wood with curved edges approximately 4,5x9x160 cm.
• 2 specially shaped rectangular birch plywood colored with internal angles of about 45 ° and 135 °, inscribed in a rectangular rectangle of approximately 110×230 cm, 2 cm thick.

Between the 2 x 20×172 cm woods there are 6 woods 4,5x6x84,5 cm per 20 cm. On them are applied the 6 woods 4,5x20x84,5 cm as presses.

The handrail is made as follows: The 2 woods 4,5x9x160 cm.

they are facing each other upwards. In these, they are screwed vertically 4,5x9x90 cm 2 by 2 on each side. Between the stairs wood 20X 172 cm, the wood 4,5x9x160 cm and the vertical wood 4.5x9x90 cm the rectangular gap on each side of the staircase is covered with birch plywood.

 

SQUARE SHEEP

 

The square cover is approximately 122x122x70cm and has a hole-to-center dimension of 102.5cm on each side.

The cover is manufactured by the rotary extraction method molded. It is formed of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.

Each color, which is non-toxic, is applied by rotary extraction of the mold. These materials are disciplined by:

• ASTM – D – 790 (Flex Modulus – Flexible elements)
• ASTM – D – 638 (Tensile Strength)
• ASTM – D – 648 (Heat Distortion Temperature – Heated Distortion)
• ARM – STD (Low Temperature Impact – low temperature impact effect)

ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.

 

 

SLIDE STRETCH WAVES 122 cm.

 

The straight corrugated slide has a height of about 122 cm and a projection length of 215 cm.

Manufactured by the rotary extraction method. It consists of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.

Each color, which is non-toxic, is applied by rotary extraction of the mold. It is a one-piece and mounted with a one-piece Hood cover of the same material for protection against falls

These materials are disciplined by:

• ASTM – D – 790 (Flex Modulus – Flexible elements)
• ASTM – D – 638 (Tensile Strength)
• ASTM -D- 648 (Heat Distortion Temperature- Heated Distortion)
• ARM – STD (Low Temperature Impact – low temperature impact effect)

The diameter of the side walls should be at least 5 cm thick.

Exceptions should be mentioned.

ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.

 

HOODS

 

The slide guard protects children from sitting in the seat to avoid accidents. It is 105 cm high, 87 cm wide and approximately 10 cm wide.

They are manufactured by the method of rotary extraction into molds. It consists of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.

Each color, which is non-toxic, is applied by rotary extraction of the mold.

These materials are disciplined by:

• ASTM – D – 790 (Flex Modulus – Flexible elements)
• ASTM – D – 638 (Tensile Strength)
• ASTM – D – 648 (Heat Distortion Temperature – Heated Distortion)
• ARM – STD (Low Temperature Impact – low temperature impact effect)

ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.

 

PROTECTIVE FRAMEWORK-PANEL

 

The protective frame measures approximately 85X97X6 cm. It consists of:

• 2 wooden columns approximately 4X6X97 cm.
• 1 plywood of approximately 85,5X90x2 cm birch color.

Between the pillars is placed the birch plywood, approximately 85,5X90x2 cm, in which reliefs or themes can be carved. Place the protective frame flat above the loft floor and secure it to the loft pillars.

 

TIMBER

 

The wood used is composite non-stick Swedish pine timber, in accordance with EN 351. It is manufactured with special compound (welding of wood) in different sections depending on the intended use.

COMPOSITE wood is 40% stronger than whole wood. It has a strength of 360 kp / m2 and a specific weight of about 480 kg / m3.

• Contains about 15% moisture
• Contains minimal juices (resin) compared to other pine family trees in other countries (weather in Northern Sweden up to -25 ° C)
• Has thermal conductivity s = 0.10 Kcal / Mho and sound insulation 3.5 times greater than concrete or brick of equal thickness.
• It has antimagnetic properties and is a poor conductor of electricity
• Resistant to fire and classified in categories F30 and F60 (by DIN 4120) according to its cross-section.
• When the outer part of the cross-section burns, its interior protects and retains its durability.
• It is processed just like commercial wood
• Maintains its shape and distorts or creates minimal fractures
• Annual wood rings are usually perpendicular to the long side of the cross-section with a significant increase in the mechanical strength of this surface, if applied to floors.

All corners of the wood are planed with a radius of about 5 mm.

 

PAINTED SYMBOL COLORS

 

The plywood elements required for our constructions are approximately 20 mm thick and are made of 1.5 mm thick laminated wood with pressurized heat sealant using non-toxic phenolic base resins. They are painted with water-soluble paints to which no seals, thinners or paints containing lead, chromium, cadmium or other heavy metals have been attached. The colors are also very resistant to adverse weather conditions.

The above plywood sheets are in accordance with EN 314-2. The quality of the plywood is such that no further processing is required before painting, such as, for example, stocking, and reliefs and themes can be engraved.

 

PLASTIC INFORMATION

The plastic components required to manufacture the equipment are highly resistant to UV radiation and adverse weather conditions. Preferred are recyclable materials such as polyethylene (PE) or polypropylene (PP). Specifically all screws protruding from the equipment over 5 mm are covered with polypropylene (PP) plastic plugs. They are also safe for the safety and health of children.

METALLIC ELEMENTS

The metallic elements used in the manufacture of the equipment (screws, joints, etc.) are made of metals either thermo-galvanized or electro-galvanized, where the surface preparation has been preceded by sandblasting or stainless steel. The dimensions and cross-sections of the metallic elements are sufficient to accommodate (with an appropriate safety factor) the loads for which they have been designed to withstand corrosion and adverse weather conditions.

PAINTS

The varnishes and colors that protect the wooden parts are specially designed for the climate of our country (temperature changes, open or closed areas etc.) are completely harmless to the users (they do not contain lead, chromium, cadmium and other heavy metals) ) and give great strength to our constructions.

For their anticorrosive protection, the metal parts are processed for polishing, followed by a coating of polyzinc (zinc) and then electrostatic, two-layer polyester powder coating.

 

PACKING

The following procedure is used for fixing the equipment:

At this point where the column is to be placed, an 80 cm deep pit is opened. about 60cm in diameter. Then, after the column is inserted, the pit is filled with frusto-concreted concrete until it reaches 10 cm. from the ground surface, where it is covered with soil.

Only ground irons, which hold each column at a distance of about 10 cm from the ground, are prevented on the ground in order to prevent the wood from being corroded by soil moisture.

 

All production work processes for the processing of raw materials are carried out according to:

• EN 1176 standards 1-6,
• ISO 9001: 2015 quality system
• The ISO 14001: 2015 environmental management system