WOODEN STRUCTURE 0010-289

 

0010-289

The composite instrument has a total dimension of 1310×755 cm and a height of 402 cm and includes:

• 1 loft with a height of 40 to 60 cm.
• 1 horizontal scale with links
• 1 horizontal scale
• 1 double monozone
• 1 semi-circular metal climbing
• 1 staircase for loft height 122 cm.
• 3 square lofts 122 cm high
• 1 loft with escalating height from 142 to 162 cm.
• 1 semicircular bridge
• 1 landing of 122 cm.
• 1 corrugated slide height 122 cm.
• 1 tunnel slide 162 cm high
• 3 squares cover
• 1 pair of safety handles
• Protective frame with railings
• protective frame
• plugs for screws
• mounting bases

SQUARE LOFT 122 cm (with square cover)

The 122 cm loft has a total dimensions of 111,5X111,5X362 cm and consists of:

• 4 wooden pillars 9X9 cm and 302 cm high.
• 4 9x9x93.5 cm wood from which approximately 4x4x93.5 cm is removed along a piece.
• 1 Wireness Plywood, one side of which has a dark brown relief embossed floor. Its dimensions are 99X99 cm and its thickness is 21mm.
• 1 square polyethylene cover that applies to the top of the 4 columns.

The vertical wooden columns of height 302 cm are pierced at points of about 116 cm and 117 cm, one on each of the sides connected to the loft, from their base to the floor of the loft. These holes are fitted with ύ 15 mm steel bores with a length of 75 mm. It has two nuts in the corresponding height mounted on the wood hole. It is fitted with two 3 / 8X13 screws. The hole in the wood is sealed with a polypropylene (PP) plug.

The floor consists of 4 9x9x93.5cm woods, on which the wireness plywood that forms the loft floor is supported.

LOFT STAIRCASE 122 cm (for ages 3 and up)

The staircase for loft height 122 cm has dimensions of 93×172 cm and projection length of loft 114 cm. Consists of:

• 2 woods approximately 4,5x20x172 cm.
• 5 woods approximately 4,5x20x88 cm.
• 5 woods approximately 4,5x6x84,5 cm.

The stair handrail for the staircase 122 cm consists of:

• 4 wood with curved edges approximately 4,5x9x90 cm.
• 2 woods with curved edges approximately 4,5x9x160 cm.
• 2 specially shaped rectangular birch plywood colored with internal angles of about 45 ° and 135 °, inscribed in a rectangular rectangle of approximately 110×230 cm, 2 cm thick.

Between the 2 x 20×172 cm woods there are 5 4,5x6x84,5 cm x 20 cm woods. On these 5 5,5x20x88 cm woods are applied as presses.

The handrail is made as follows: The 2 woods 4.5x9x160 cm are facing each other and facing upwards. They are screwed vertically, 4,5x9x90 cm 2 by 2 on each side. Between the stairs wood 20X 172 cm, the wood 4.5x9x160 cm and the vertical wood 4.5x9x90 cm the rectangular gap on each side of the staircase is covered with birch plywood.

ESCALATING LOFT 142 => 162 cm

The escalating loft 142-162 cm has a total dimension of 111,5X111,5X402 cm and consists of:

• 4 wooden pillars 9X9 cm and 342 cm high.

The 2 triangular floors consist of:

• 2 woods 8×4,5×132 cm.
• 4 9X9X93.5 cm wood from which 4X4X93.5 cm long piece is removed.
• 2 Wireness plywood, one side of which features an embossed anti-skid floor, dark brown in the shape of an isosceles triangle with a bearing 132 cm and a 93.5 cm isosceles sides forming the loft floor.

The woods (8×4,5×132 2 pcs and 9x9x93,5 4 pcs) have bore holes for mounting support to the loft pillars through Ø15 mm and 75 mm metal studs and are fitted with two 3 / 8×13 mm screws. the wood opening is sealed with a polypropylene (PP) plug.

SEMI-CIRCULAR BRIDGE

The bridge is approximately 200×109 cm and 94 cm high and consists of:

• 4 columns approximately 7×4,5×94 cm in diameter.
• 4 curved woods approximately 4.5x10x191 cm.
• 2 curved woods approximately 8x10x200 cm.
• 2 woods approximately 9x9x99 cm.
• 2 birch plywood colored 191x75x2 cm approx.
• 10 woods approximately 4x20x99 cm.

The floor of the semicircular bridge consists of two 8x10x200 woods and two 9x9x99 woods that form the frame of the bridge floor. In this frame are fixed the 10 4X20X99 wood flooring.

The two side handrails consist of a frame consisting of two 4,5x10x191 curved wood and 2 7×4,5×94 2 columns each and the intermediate gap is filled by the colored birch plywood. Various representations or themes can be etched on the birch plywood.

DOWNHILL – FIRE (for loft height 122 cm)

The downhill – fire extinguisher activity consists of a galvanized metal plate of hot rolled cross section Ø 32 mm and a height of 300 cm.

Top section with galvanized metal plate hot-rolled cross-section και 32 mm and 3 mm thick 93.5 cm elliptical “P” shape with attachment awaiting the loft columns and height specified in EN 1176. Bottom and 2 pcs of safety handles are applied on the loft floor.

TUNNEL SLIDE 162

The tunnel slide has a height of 162 cm. It is manufactured by the molding rotary extraction method. It is formed of linear low density polyethylene with UV stabilizers and has been treated with ‘High Level Antistatic’ (static electricity neutralization treatment).

Each color, which is non-toxic, is applied by rotary extraction of the mold. These materials are disciplined by:

• ASTM – D – 790 (Flex Modulus – Flexible elements)
• ASTM – D – 638 (Tensile Strength)
• ASTM – D – 648 (Heat Distortion Temperature – Heated Distortion)
• ARM – STD (Low Temperature Impact – low temperature resistance effect)

ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service

STRAIGHT CORRUGATED SLIDE 122 cm.

The straight corrugated slide has a height of 122 cm and a projection length of 215 cm.

It is manufactured by the rotary extraction method. It consists of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.

Each color, which is non-toxic, is applied by rotary extraction of the mold. It is a one-piece and mounted with a one-piece Hood cover of the same material, for protection against falls

These materials are disciplined by:

• ASTM – D – 790 (Flex Modulus – Flexible elements)
• ASTM – D – 638 (Tensile Strength)
• ASTM -D- 648 (Heat Distortion Temperature- Heated Distortion)
• ARM – STD (Low Temperature Impact – low temperature resistance effect)

The diameter of the side walls should be at least 5 cm thick.

Exceptions should be mentioned.

ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.

HOODS

The slide guard protects children from leaving their seats in order to avoid accidents. It is 105 cm high, 87 cm wide and approximately 10 cm wide.

They are manufactured by the method of rotary extraction into molds. It consists of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.

Each color, which is non-toxic, is applied by rotary extraction of the mold.

These materials are disciplined by:

• ASTM – D – 790 (Flex Modulus – Flexible elements)
• ASTM – D – 638 (Tensile Strength)
• ASTM – D – 648 (Heat Distortion Temperature – Heated Distortion)
• ARM – STD (Low Temperature Impact – low temperature resistance effect)

ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.

SQUARE COVER

The square cover is approximately 122x122x70cm and has a hole-to-center distance of 102.5 cm on each side.

The lid is manufactured by the rotary extraction molding process. It is formed of linear low density polyethylene and with the addition of materials that provide protection from UV radiation and against static electricity.

Each color, which is non-toxic, is applied by rotary extraction of the mold. These materials are disciplined by:

• ASTM – D – 790 (Flex Modulus – Flexible elements)
• ASTM – D – 638 (Tensile Strength)
• ASTM – D – 648 (Heat Distortion Temperature – Heated Distortion)
• ARM – STD (Low Temperature Impact – low temperature resistance effect)

ASTM = the American Society for Testing and Materials, the American Materials Testing and Testing Service.

PROTECTIVE FRAMEWORK-PANEL

The protective frame measures approximately 85X97X6 cm. It consists of:

• 2 wooden columns approximately 4x6x97 cm.
• 1 plywood of colored birch approximately 85,5X90x2 cm.

Between the pillars is the birch plywood, approximately 85,5x90x2 cm, in which relief figures or themes can be carved. Place the protective frame flat above the loft floor and secure it to the loft pillars.

HORIZONTAL SCALE WITH CLICKS

The horizontal scale with links is 260X100X195 cm and consists of:

• 4 wooden columns 9X9 in cross section and 195 cm high.
• 1 Ø 1 ½ ”tube “I” shaped of 260 cm length and 82 cm width.
• 6 metal rings with an inner diameter of 25 cm.

The scale frame is made up of four wooden columns. The “I” shaped tube is connected to the columns. The metal rings are attached to the tube.

HORIZONTAL SCALE

The horizontal scale is 100x270x195 cm and consists of:

• 2 columns 9×9 cm and 195 cm high.
• 2 horizontal beams 9X9X270 cm.
• 7 galvanized hot rolled sheets with a cross-section Ø 60, 2 mm thick and 64 cm long.
• 48 plastic plugs.

The horizontal beams are nailed to the inside of the two columns and leave a gap of 64 cm between them so that the hot rolled sheets can be positioned. The 8 sheets are positioned every 30 cm between the horizontal woods as handles. The remaining 3 are applied every 30 cm to the columns, starting 40 cm from their base as presses. The plates are then covered with the plugs inside and outside the columns and the horizontal beams.

DOUBLE MONOLITH

The 270X195 cm double wooden monolayer is made up of three 9×9 cross sections made of composite Swedish pine wood, in accordance with EN 351. They are coated with two layers of water-soluble paint and one layer.

All upright posts are 121 cm apart

At the top they have hot-rolled laminated sheets cross section 1” that are mounted to the stanchions with special PVC joints with a special lid that protects the screw that is not easily accessible.

SEMI-CIRCUIT METAL CLIMBING

The semi-circular metal climbing is 210×110 cm and 210 cm high and consists of:

• 3 pcs metal columns Ø 3’’ and 210 cm high
• 4 pcs hot rolled steel plates Ø 1 ¼ ”and approximately 153 cm long
• 8 pcs 200 cm polypropylene (PP) coated security ropes.
• 8 pcs 150 cm polypropylene (PP) coated security ropes.
• 32 pcs metal fasteners mounted on the ends of the ropes.

The metal climbing frame consists of three steel columns 210 cm and Ø 3 ″ which are positioned in such a way as to form a semicircle 210 cm in diameter.

These three columns are connected by means of curved laminated sheets Ø 1 ¼ ”and about 153 cm long which are welded together to form the semicircle. The ropes are then mounted (8 pcs perpendicular to the joints and 8 pcs in the semicircle direction).

SAFETY HANDLES

The safety handles are metallic electrostatic paint with vertical alignment in two, with the inner wrapped at the top. It has a metal blade at its bottom and a point at the top. They are made of a tube Ø 32 mm approximately 80 cm high and spaced apart according to EN 1176. After being degreased, they are coated with polyzinc (zinc) and then electrostatic powder coating.

The safety handles are fitted in places where there are no entry / exit protectors (panels, railings etc.).

BACKPACK BASES

For fixing the instrument to the ground, each pair has a pair of mounting bases.

The mounting brackets consist of two galvanized metal plates and then painted with electrostatic paint, shaped “P” and about 100x12x4cm thick and 0.5cm thick, which “embrace” the column and are joined by passing screws 5 / 8 ″ X15. At the bottom there is a metal flange to hold them in the concrete pit.

Only ground irons, which hold the column at least 5 cm above the ground, are prevented from being ground in order to prevent the wood from being eroded by soil moisture.

TIMBER

The wood used is composite non-stick Swedish pine timber, in accordance with EN 351. It is manufactured with a special compound (welding of wood) in various sections depending on the intended use.

COMPOSITE wood is 40% stronger than whole wood. It has a strength of 360 kp / m2 and a specific weight of about 480 kg / m3.

• Contains about 15% moisture
• Contains minimal juices (resin) compared to other pine family trees in other countries (weather in northern Sweden up to -25 ° C)
• Has thermal conductivity s = 0.10 Kcal / Mho and sound insulation 3.5 times greater than concrete or brick of equal thickness.
• Has antimagnetic properties and is a poor conductor of electricity
• Resistant to fire and classified in categories F30 and F60 (by DIN 4120) according to its cross-section.
• When the outer part of the cross-section burns, its interior protects and retains its durability.
• It is processed just like commercial wood
• Maintains its shape and distorts or creates minimal fractures
• Annual wood rings are usually perpendicular to the long side of the cross-section with a significant increase in the mechanical strength of this surface when applied to floors.

All corners of the wood are planed with a radius of about 5 mm.

PAINTED BIRCH PLYWOOD

The plywood elements required for our constructions are approximately 20 mm thick and are made of 1.5 mm thick laminated wood with pressurized heat sealant using non-toxic phenolic base resins. They are painted with water-soluble paints to which no seals, thinners or paints containing lead, chromium, cadmium or other heavy metals have been attached. The colors are also very resistant to adverse weather conditions.

The above plywood sheets are in accordance with EN 314-2. The quality of the plywood is such that no further processing is required before painting, such as, for example, stocking, and reliefs and themes can be engraved.

PLASTIC INFORMATION

The plastic components required to manufacture the equipment are highly resistant to UV radiation and adverse weather conditions. Preferred are recyclable materials such as polyethylene (PE) or polypropylene (PP). Specifically all screws protruding from the equipment over 5 mm are covered with polypropylene (PP) plastic plugs. They are also safe for the safety and health of children.

METAL ELEMENTS

The metallic elements used in the manufacture of the equipment (screws, joints, etc.) are made of metals either thermo-galvanized or electro-galvanized, where the surface preparation has been preceded by sandblasting or stainless steel. The dimensions and cross-sections of the metallic elements are sufficient to accommodate (with an appropriate safety factor) the loads for which they have been designed to withstand corrosion and adverse weather conditions.

PAINTS

The varnishes and the colors that protect the wooden parts are specially designed for the climate of our country (temperature changes, open or closed areas etc.) are absolutely harmless to the users (they do not contain lead, chromium, cadmium and other heavy metals). ) and give great durability to our constructions.

For their anticorrosive protection, the metal parts of the mill are processed for polishing, followed by a coating of polyzinc (zinc) followed by a two-layer, electrostatic powder coating.

PACKING

The following procedure is used for fixing the equipment:

At this point where the column is to be installed, a pit about 80 cm deep and 60 cm in diameter is opened. Then, once the column is inserted, the pit is filled with fractured cone-shaped concrete until it reaches 10 cm from the ground surface, where it is covered with soil.

Only ground irons, which hold each column at a distance of about 10 cm from the ground, are prevented on the ground in order to prevent the wood from being corroded by soil moisture.

 

All production work processes for the processing of raw materials are carried out according to:

• EN 1176 standards 1-6,
• ISO 9001: 2015 quality system
• The ISO 14001: 2015 environmental management system